adhesive friction
英
美
[网络] 黏著摩擦
双语例句
- It provides theoretical foundation for determining the size of pressing load. Finally, a fractal model of adhesive friction coefficient is proposed by comparing the normal elastic load with the normal plastic load acting on particle contact points.
最后，通过比较作用于颗粒接触点的法向弹塑性载荷，提出了粘着摩擦系数的分形模型。 - With the increase of the concentrations of peroxide solutions, the degree of adhesive wear weakened and the friction coefficient decreased. In high concentration of peroxide solutions, the main wear mechanism of ceramic materials was corrosive wear, abrasive wear and the friction coefficient increased.
随着H202介质溶液浓度的增大，粘着作用减弱，摩擦系数减小，高浓度H202介质溶液中，Si3N4陶瓷材料的磨损以腐蚀磨损和磨粒磨损为主，摩擦系数增大。 - Calculation of Rolling Strain Velocity in Consideration of Adhesive Friction and Slide Friction
考虑粘着摩擦和滑动摩擦的轧制变形速度的计算 - We also find that, due to the water vapor condensation, the adhesive force and friction coefficient on sample surfaces increase first, then decrease with the relative humidity increase.
由于强的亲水性，样品表面的摩擦系数和黏附力随着湿度的增大先逐渐增大，然后急剧减小。 - As adhesive, matrix resin accounted for a larger proportion in non-metallic and semi-metallic friction material. Its performance direct impacts on the using performance of friction material.
基体树脂作为粘接剂，在非金属、半金属摩擦材料中所占的比例较大，其性能的好坏直接影响摩擦材料的使用性能。 - This paper sets up a mathematical model for calculating thermal balance of plunger-cylinder wall friction pair in axial plunger pump, analyzes the cause of producing adhesive wear on the friction pair, and puts forward a way to solve the problem.
本文提出了轴向柱塞泵柱塞&缸孔摩擦副热平衡计算的数学模型，进而分析了这对摩擦副产生粘着磨损的原因，并提出了解决办法。 - Thermal shock cracking in friction surface, over heated and over burned microstructure in sub surface, adhesive element diffusion from surface to center occur due to friction heat. Layer delamination occurs also on the worn surface of the steel.
因摩擦热的影响，制动后钢的摩擦表面出现热震开裂，表层组织过热甚至过烧，表面的粘着物由表向里扩散； - The main contents are as following: ( 1) Discusses the adsorption force consists of adhesive force, negative pore water pressure and side friction.
本文的主要内容：（1）论述了吸附力由粘着力、负孔隙水压力、侧摩阻力组成。 - It's believed that the main wear mechanism is adhesive under dry friction, while abrasive with water lubrication, and the friction and wear performances of the composites are greatly improved with water lubrication.
水润滑条件下复合材料的摩擦磨损性能远优于干摩擦条件下的性能.干摩擦条件下复合材料的磨损机制主要为黏着磨损，水润滑条件下则以磨粒磨损为主。 - Friction characteristics of PC and its alloys can be explained by adhesive friction theory, and wear of these materials are controlled by adhesive, abrasive and fatigue wear mechanisms.
聚合物及其合金的摩擦特性可由粘着摩擦理论解释，其磨损过程主要受粘着、磨粒和疲劳机理控制。